Camera Parts

Thanks for visiting our site!
Body Battery
Checkout Ebay Auctions For The Cheapest Prices

Check out Amazon:

Here are some more information for Body Battery:

Before you begin installation, please ...

- Use caution when handling iPaq and the battery.

- Use common sense care for handling the battery such as not flexing (ie, bending), away from metal, away from extreme heat, etc.

- Make sure that all data in iPaq have been backed up. All data will be lost after installing the new battery.

- Read the whole instruction before your first attempt to replace the battery. This will help you to visualize the process before it has begun.

1. Turn the power off, and also make sure the reset key on the bottom of the unit is turned off to ensure the power is completely off.

2. Take stylus out from iPaq before proceeding.

3. Using Torx T6 screwdriver, get the four screws off from each corner. Make sure not to misplace screws. Split the back cover from the main body using your fingernail or any flat type device such as a Phillips screwdriver. Just make sure that you

don't scratch the surface if using a screwdriver.

4. Once the back cover is split from the main body, open the back cover from the top. Do not pull it out all the way as the battery is attached to the main board via a flexible PCB connector. Note: A, hard reset button slide door and stylus lock are not attached to the body, and therefore, they may be loose as the back cover is pulled off. They are easy to put back but it is wise to take a note of their location and position.

5. As you pull the back cover up gently, you will see a connector between the battery and the main board. Gently remove the connector from the battery. Please note that the battery is glued to the back cover, and can be removed after you

disconnect the battery connector from the main board.

6. Once you have the old battery taken out, align the new battery so that the edge of the battery that is closer to the connector goes to the bottom (ie, the taped side is the top).

7. Firmly press the connector to the battery. Make sure that all corners are inserted firmly.

8. Starting from the bottom, reinsert the backcover. Do not force the cover when closing. This means that the battery is not properly seated onto the back cover. Simply realign the battery so that it is properly seated.

9. Put four screws back, and turn the reset key and the power button on, in that order, to ensure that the unit operates normally.

10. You should fully recharge the battery, and leave it charged for additional 30-60 minutes after a full charge indicator is on. This ensures that the battery is fully charged.

A full guide with pictures are located at www.fusionteq.com

James Kim is a project manager at Fusionteq Co, a solution provider for iPaq battery replacement.

How to Increase the Life of a Mobile Phone Battery?

Mobile phones have really changed our life style. We are connected with each other throughout the world with the help of a mobile phone. Whether a person is in train, bus or in an aircraft, he is connected with the world as good as in his office or home. Thanks to mobile phone technology to bring a sea change in human life. Though mobile phone technology is not very old, but mobile phone has penetrated the world. Now mobile phones have their thousand models from single manufacturers with different battery model. There are hundreds of manufacturers of the world level.

Mobile phone battery is an important accessory of a phone. It acts like a heart in human body. Imagine if battery of a mobile phone get totally discharged. There is no alternate; of course, if battery source is accessible well otherwise, mobile phone becomes unwanted weight. While going to buy a mobile phone a user should look for quality of battery. A battery has a cathode, an anode connected with its body, which contains an electrolyte. These are not only the parts of the battery to be checked but there are several other aspects to be checked before placing an order.

The cathode and anode are metal strips, these strips have a normal tendency to react with moisture, and form oxidized substance. This substance is non-conductor, which blocks flow of the current to the mobile phone. All type of phones has such problem more or less depending upon quality of material used in making strips. Also as a precaution it is advised to keep mobile phone away from moisture.

As wide classification of batteries, mobile phone use dry battery. There is innumerable type of mobile phone battery, available in market. These batteries can be alkaline, lead acid, lithium dioxide, Nickel cadmium, lithium ion etc. Lithium batteries are mostly used in mobile phones. These are rechargeable type of batteries, which can be recharged by connecting it with a normal plug through a charger. These batteries are light in weight smaller in size than general-purpose batteries. And these batteries store very high-density charge. They have immunity from side effect memory and data transfer.

Enhancement in the capabilities of mobile phones facilitates the users to use it more and more for different applications. Obviously, then there is requirement of more power for the cell phone and finally whole load falls on battery. It becomes imperative for the users to be conversant with the precautions taken to protect their mobile phone battery.

orange phone

About the Author

Ian Ball is an expert on the telecomms industry

How does battery acid effect your body?

touched a leaking battery, still using the item it was in(and it STILL works!)

Acid battery contains concentrated H2SO4 (sulphuric acid). The acid is a powerful dehydrating agent so it can burn the skin and affect layers under the skin. A lot of heat is also evolved and can cause blisters/burns It burn in cotton cloths and make holes.

Extent of damage will depend on concentration of acid, duration of contact, quantity of acid, area in contact, part of body ( some areas are more delicate hence more damage).

Amount of acid in battery is quite large so even if some acid leaks out it will continue to work.
Concentration of acid also chenges during its usage. On drawing current the acid becomes dilute ane dilute. On charging the acid becomes more and more concentrated.

If you did not get more damage may be acid was dilute. The leaked acid will also become dilute as it will catch miosture from air and will become dilute and may cause less damage ( I am not suggesting to be careless with leaking acid it can cause great damage be careful).

MEMS device generates power from body heat
(PhysOrg.com) -- In an attempt to develop a power source that is compact, environmentally friendly, and has an unlimited lifetime, a team of researchers from Singapore has fabricated an energy harvesting device that generates electricity from body heat or any environment where there is a temperature gradient. Their device, called a thermoelectric power generator, attaches to the body and ...

Thanks for visiting!